Menu
0
Bezoek ook eens onze winkel in Den Haag
Vragen? Bel 070 - 36 32 777
Voor 15.00 besteld? Vandaag verzonden
€75,00
In Basket
Michell Engineering Rega 3-Point VTA Adjuster 2
Michell Engineering Rega 3-Point VTA Adjuster 2
Michell Engineering Rega 3-Point VTA Adjuster 2

Michell Engineering Rega 3-Point VTA Adjuster 2

€75,00Incl. VAT (BTW)
Op voorraad

Michell Engineering Rega 3-Point VTA Adjuster 2 fixing VTA (Vertical Tracking Angle) Arm Adjuster has been designed for the range of Rega arms (RB-251 and RB301) that use the recently introduced 3-point fixing. Once installed, the user can adjust the ver Lees meer..

Ships Today
  • Voor 15.00u besteld?

    Dan wordt je bestelling vandaag verzonden
  • Gratis verzending

    Voor orders vanaf €80,00
  • Een echte winkel

    Kom ook eens bij ons langs in Den Haag
  • Klantenservice?

    Bel 070 - 36 32 777 voor vragen, tips of advies

Productomschrijving

Michell Engineering Rega 3-Point VTA Adjuster-2

Note:  this fitting does NOT work with Rega 700, 808 & 1000

The Rega 3-point fixing VTA (Vertical Tracking Angle) Arm Adjuster has been designed for the range of Rega arms (RB-251 and RB301) that use the recently introduced 3-point fixing. Once installed, the user can adjust the vertical tracking angle in minute increments without losing the rigid 3-point mounting so important to proper sound reproduction.

The VTA adjustor, at its minimum setting, raises the tone arm by 2mm, which is the same as the thinnest setting on the moulded adjuster available from Rega. It comes packed with two different thickness adjuster rings (the thinner ring is designed to lift the tonearm base 0 to 2mm and the thicker ring will lift the base 2 to 4 mm) and all of the fixings necessary as well as a nylon nib to help rotate the base notches if access is tight.

======

The Michell VTA adjuster 3 allows you to easily adjust the height of your tonearm, so it is perfectly level no matter what cartridge you choose to use. Correctly setting the vertical tracking angle (VTA) and subsequently the stylus rake angle (SRA) for your cartridge, allows the stylus to perfectly track the vinyl groove, optimising the amount of detail extracted from the recording.
 
**Please note** The VTA/SRA adjuster’s base is 2mm thick and once installed and set to its lowest position, the adjuster will raise your tonearm by 2mm. If you are using the adjuster with a Michell Engineering Gyro or Orbe model turntable then please fit the shorter 10mm arm plate spacers supplied, to compensate for the added height of the adjuster. If you wish to use the adjuster on a turntable where the arm plate/board cannot be lowered, then please note that your tonearm will be 2mm higher before any adjustment has taken place. The VTA/SRA adjuster comes with three nylon washers, these are to be used if you wish to raise the tonearm more than the 3.5mm of lift available using the adjuster on its own. 
 
Note:  this fitting does NOT work with Rega 700, 808 & 1000
 
 

Reviews

0 beoordelingen

Specifications

Rega 3-Point VTA Adjuster 2

0 beoordelingen

Beoordeel Michell Engineering Rega 3-Point VTA Adjuster 2

Michell Engineering Rega 3-Point VTA Adjuster 2 fixing VTA (Vertical Tracking Angle) Arm Adjuster h..

Subscribe to our newsletter

Subscribe

Account aanmaken

Door een account aan te maken in deze winkel kunt u het betalingsproces sneller doorlopen, meerdere adressen opslaan, bestellingen bekijken en volgen en meer.

Register (registreer)

Recent toegevoegd

You have no items in your shopping cart

Total incl. VAT/BTW:€0,00
Bestel nog voor €80,00 en de verzending is gratis

Taal & Valuta